| SL. NO. | PART NUMBER | PART DESCRIPTION |
| 1 | A 1380011-2 | COUPLING GEAR TYPE |
| 2 | A 1410043-1 | SUSPENSION MOTOR NOSE |
| 3 | A 1410043-10 | SUSPENSION MOTOR NOSE |
| 4 | A 1410044-1 | SUSPENSION MOTOR NOSE |
| 5 | A 14115110 | BOOT, TRACTION MOTOR (MATERIAL : LATHER) |
| 6 | A 1411519 | BOOT, TRACTION MOTOR (MATERIAL : LATHER) |
| 7 | A 16010919 | ELEMENT,LUBRICATING OIL STRAINER |
| 8 | A 1601492-2 | ELEMENT, LUB OIL STRAINER |
| 9 | A 1636137 | DRESSER ELBOW – 1/2″ X 90 Degree |
| 10 | A 16392012 | DRESSER COUPLING – 4.1/2″ ID 5″ OD |
| 11 | A 1639301 | DRESSER COUPLING – 1″ ID |
| 12 | A 16393013 | DRESSER COUPLING – 2″ ID |
| 13 | A 16393014 | DRESSER COUPLING – 1/2″ ID |
| 14 | A 1639302 | DRESSER COUPLING – 3″ ID |
| 15 | A 1639303 | DRESSER ELBOW – 1.1/2″ X 90 Degree |
| 16 | A 1639307 | DRESSER COUPLING – 2.1/2″ ID 3″OD |
| 17 | A 16393451 | DRESSER ELBOW – 1.1/4″ X 90 Degree |
| 18 | A 16393495 | DRESSER ELBOW – 1″ X 45 Degree |
| 19 | A 16396121 | DRESSER ELBOW – 2″ X 90 Degree |
| 20 | A 16396140 | DRESSER ELBOW – 2″ X 45 Degree |
| 21 | A 16396148 | DRESSER ELBOW – 3/4″ X 45 Degree |
| 22 | A 16396159 | DRESSER ELBOW – 3/4″ X 90 Degree |
| 23 | A 16702710 | COUPLING HOLE SET TYPE |
| 24 | A 16702714 | CPUPLING HOTTEST TYPE |
| 25 | A 1670331 | BEARINGS, SHAFT AND HOUSING |
| 26 | A 1671321 | FLEXABLE PIPE COUPLING 3″ |
| 27 | A 1671322 | COUPLING |
| 28 | A 16713322 | FLEXABLE PIPE COUPLING 2.1/2″ |
| 29 | A 1672166 | HOUSING, BEARING |
| 30 | A 16721816-1 | SHAFT, RADIATOR FAN DRIVE |
| 31 | A 1672182 | SHAFT, IMPELLER, WITH KEY, FOR TM BLOWERS |
| 32 | A 1672189 | SHAFT, FOR RADIATOR FAN DRIVE |
| 33 | A 2140013 | BASE DOOR ASSEMBLY |
| 34 | A 2140013-2 | BASE DOOR ASSLY. |
| 35 | A 2140013-3 | BASE DOOR ASSEMBLY |
| 36 | A 21410166 | MAIN BEARING SHELL INTERMEDIATE |
| 37 | A 21410326 | MAIN BEARING SHELL CENTER |
| 38 | A 21410365 | MAIN BEARING SHELL THRUST NO 9 |
| 39 | A 21410365-1 | BEARING MAIN THRUST |
| 40 | A 2141427 | WEAR PLATE MAIN BASE |
| 41 | A 2151021 | NUT SPECIAL CON ROD BOLT ( SLOTTED ) |
| 42 | A 2151022 | NUT CONROD BOLT |
| 43 | A 21511034 | DOWEL PIN |
| 44 | A 21511041 | DOWEL |
| 45 | A 2151261 | NUT GEAR TO SHAFT |
| 46 | A 21512866 | CAP SCREW |
| 47 | A 21513518 | BOLT , TANK TO CORE , 3/8-16X1-1/8 IN. |
| 48 | A 2151395 | NUT |
| 49 | A 21514267 | STUD FOR VALVE LEVER SUPPORT & CASTING |
| 50 | A 2151452 | GASKET, CYL. LINE TO BLOCK ( TOP ) |
| 51 | A 2151455 – 1 | GASKET LINE TO BLOCK ( BOTTOM ) |
| 52 | A 2151456 | GASKET LINE TO BLOCK ( CENTER ) |
| 53 | A 21518817 | STUD, SPECIAL, FOR COVER |
| 54 | A 2151921-1 | ADJUSTING SCREW YOKE, AIR & EXH |
| 55 | A 2151942 | NUT, GOVERNOR DRIVE |
| 56 | A 2152358 | SCREW,POWER CYLINDER,3/8-16X1 IN. |
| 57 | A 2152716 | KEY IMPELLER TO SHAFT |
| 58 | A 2152788-1 | SNAP RING (PISTON PIN RETAIN RING) |
| 59 | A 21528312 | TAPER DOWEL |
| 60 | A 2153213 | LOCKNUT, 3/4-10 |
| 61 | A 2153271 | NUT ADJ VALVE LEVER PART FOR ALCO ENGINE |
| 62 | A 2153363-1 | GASKET BRANCH PIPE TO HEAD |
| 63 | A 2153403 | GROMMET (PUSHROD SLEEVE) |
| 64 | A 2153595 | GASKET INLET HEAD |
| 65 | A 2153632 | BUSHING (IN LEVER) |
| 66 | A 2153654-1 | GASKET MANIFOLD TO TURBO |
| 67 | A 2153657 | GASKET MANIFOLD TO CYLINDER HEAD |
| 68 | A 21556076 | CAPSCREW, MANIFOLD TO TURBO |
| 69 | A 2155825 | NUT IMPELLER TO SHAFT |
| 70 | A 2155826 | LOCKNUT, SPECIAL |
| 71 | A 2161332 | CAMSHAFT BUSHING INTERMEDIATE |
| 72 | A 2170017-1 | CONNECTING ROD ASSEMBLY |
| 73 | A 2171016 | PISTON PIN BUSH (BUSHING CONNECTION ROD SMALL END) |
| 74 | A 2171016-1 | CONROD BUSHING |
| 75 | A 21710226 | BEARING |
| 76 | A 2171052 | BOLT CONNECTING ROD MACH. |
| 77 | A 21711052 | BOLT CONDROD |
| 78 | A 2190114-1 | COUPLING GEAR TYPE |
| 79 | A 2190124 | OIL SEAL ASSY. |
| 80 | A 21901313 | EXTENSION SHAFT MACH. |
| 81 | A 21901316 | EXTENSION SHAFT MACH. |
| 82 | A 2191355 | HUB |
| 83 | A 2191472 | MALE SLEEVE |
| 84 | A 2191522-1 | OIL CATCHER (6 CYL. ENGINE) |
| 85 | A 2191524-1 | OIL CATCHER, GENERATOR END (“V” TYPE ENGINE) |
| 86 | A 2191532 | SEAL OIL, EXTENSION SHAFT MACH. (INTERNAL OIL SUPPLY TO VIBRATION DAMPER) |
| 87 | A 2191535-1 | OIL SEAL,EXTENSION SHAFT (EXTERNAL OIL SUPPLY TO VIBRATION DAMPER) |
| 88 | A 2191921 | FLOATING BUSHING MACH. |
| 89 | A 2221092-1 | SLEEVE NOZZLE COOLING IN CYL. HEAD (SLEEVE INJECTOR) |
| 90 | A 2221092-2 | SLEEVE |
| 91 | A 22211815 | EXHAUST VALVE SEAT INSERT ( STANDARD SIZE ) (STELLITE) |
| 92 | A 22211816 | VALVE SEAT INSERT OVERSIZE .010” |
| 93 | A 22211817 | AIR VALVE INSERT ( STANDARD SIZE ) |
| 94 | A 22211817-1 | AIR VALVE SEAT INSERT (STD. SIZE) (INSERT VALV SEAT 30° INTAKE) (STELLITE) |
| 95 | A 22211818 | INSERT (S-S BY 22211818-1) |
| 96 | A 22310227 | NOZZLE |
| 97 | A 22310227-2 | NOZZLE FUEL INJECTOR |
| 98 | A 22311210 | EXHAUST VALVE “45 DEGREE”(INCONEL) |
| 99 | A 22311211 | AIR VALVE (30 DEGREE) |
| 100 | A 2231129 | AIR & EXHAUST VALVE (45 DEGREE) |
| 101 | A 2231138 | VALVE GUIDE (AIR & EXHAUST) |
| 102 | A 2231139 | GUIDE, .020 O/S |
| 103 | A 2231174-2 | YOKE, AIR & EXH VALVE (MACH) |
| 104 | A 223118 | AIR & EXHAUST VALVE GUIDE ( STANDARD SIZE ) |
| 105 | A 2231231 | SEAT, VALVE SPRING |
| 106 | A 22312610 | SEAT, SPRING LOWER |
| 107 | A 2231295 | SPRING INJECTOR (PRESSURE ADJUSTING) |
| 108 | A 2231391 | SPACER |
| 109 | A 2231402 | SPACER, VALVE STOP |
| 110 | A 2240014-1 | PUSHROD AIR AND EXHAUST ( VARILLAS DE EMPUJE) |
| 111 | A 2240201-1 | LIFTER (PUSH ROD MACH.) |
| 112 | A 2240211 – 1 | VALVE LEVER SUPPORT WITH LIFTER ASSEMBLY |
| 113 | A 2241032 | RETAINER RING |
| 114 | A 2241101 | ADJUSTING SCREW |
| 115 | A 2241261 | SEAT, VALVE LIVER PUSH ROD LIFTER |
| 116 | A 2241271 | BALL THRUSH VALVE LEVER |
| 117 | A 2241281-1 | SNAP RING |
| 118 | A 2241294-1 | SLEEVE, PUSH ROD |
| 119 | A 2241324 | SHAFT, VALVE LEVER |
| 120 | A 2241342 | ROLLER , CAM FOR PUSH ROD |
| 121 | A 2241353-1 | CAM ROLLER PIN (AIR & EXT. VALVE) |
| 122 | A 2241354-1 | FULCRUM PIN FOR PUSH ROD LIFTER |
| 123 | A 2241491 | BUSHING LIFTER |
| 124 | A 2250014-4 | WATER PUMP ASSY |
| 125 | A 2250016-3 | WATER PUMP ASSLY. |
| 126 | A 2250016-4 | WATER PUMP ASSLY. |
| 127 | A 2250036 | WATER SEAL UNIT |
| 128 | A 2250037 | SEAL |
| 129 | A 22511212 | CASING WATER PUMP |
| 130 | A 2251122-1 | CASING |
| 131 | A 2251123 | CASING, WATER PUMP |
| 132 | A 22511421 | FRAME BEARING (W. P.) |
| 133 | A 22511422 | IMPELLER |
| 134 | A 22511423 | IMPELLER |
| 135 | A 2251143-4 | IMPELLER |
| 136 | A 2251149-2 | IMPELLER |
| 137 | A 2251154-2 | WATER PUMP SHAFT WITH SLEEVE |
| 138 | A 2251172 | RETAINER, THRUST BEARING WATER PUMP |
| 139 | A 2251174 | RING RETAINER |
| 140 | A 2251181-1 | SLINGER & HUB ASSY. |
| 141 | A 2251211-2 | SEAL |
| 142 | A 2251284-2 | SLEEVE (IMPELLER) |
| 143 | A 2251323 | SEAL PLATE |
| 144 | A 2251521 | HUB (RUBBER MATL) |
| 145 | A 22610511 | BLOWER INLET CASING |
| 146 | A 2261075 | BEARING SLEEVE |
| 147 | A 22611310 | BEARING |
| 148 | A 22611311-1 | WASHER, RETAINER |
| 149 | A 2261138 – 1 | BEARING THRUST WASHER COMPRESSOR END |
| 150 | A 2261139 | BUSHING |
| 151 | A 22612014 | THRUST BEARING |
| 152 | A 2261208 | BEARING BLOWER END (FOR TURBO CHARGER) |
| 153 | A 2261209 | BEARING TURBINE END (FOR TURBO CHARGER) |
| 154 | A 2261211-1 | OIL SEAL FOR TURBO CHARGER TURBINE END |
| 155 | A 2261212-1 | OIL SEAL FOR TURBO CHARGER BLOWER END |
| 156 | A 22612122 | OIL SEAL COMPRESSOR END MACH. |
| 157 | A 22612123 | OIL SEAL MACH. |
| 158 | A 2261223 | SPACER PIN |
| 159 | A 22612313 | RETAINER, TURBINE END BEARING SLEEVE |
| 160 | A 2261329 | SHAFT TURBO MACH. |
| 161 | A 2261353-2 | SPACER TURBO SUPPORT MACH. |
| 162 | A 2261478 | CARRIER BEARING MACH. |
| 163 | A 2261521 | SPECIAL BUSHING TURBO |
| 164 | A 2261526 | BEARING |
| 165 | A 2261632 | AIR SEAL, COMPRESSOR END – MACH. |
| 166 | A 2281065 | ELBOW |
| 167 | A 2281175 | RETAINING RING, TRIP LEVER TO SHAFT |
| 168 | A 2281177 | SNAP RING (RETANING RING) |
| 169 | A 22813518 | FREE END SPACER |
| 170 | A 22813519 | CENTER SPACER |
| 171 | A 22816514-1 | COVERS |
| 172 | A 2282062 | COUPLING CLAMP |
| 173 | A 2282066 | COULPLING CLAMP BELLOWS ELBOW |
| 174 | A 2282073 | END CAP |
| 175 | A 230027-1 | F.P. CONTROL SHAFT WITH COUPLING, DOGS AND LEVER, RIGHT SIDE |
| 176 | A 230028-1 | F.P. CONTROL SHAFT WITH COUPLING, DOGS AND LEVER, LEFT SIDE |
| 177 | A 2311062 – 1 | SLEEVE LINE TO BLOCK LOWER ( STANDARD ) |
| 178 | A 2320151-1 | COVER ASSEMBLY( FUEL PUMP SUPPORT) |
| 179 | A 2320193 | CROSS HEAD FOR BODY FUEL PUMP |
| 180 | A 2320261 | PIN WITH ECCENTRIC |
| 181 | A 23211320 | PIN LINK TO LEVER |
| 182 | A 2321349 | DELIVERY VALVE HOLDER |
| 183 | A 2321368 | DELIVERY VALVE ASSY. |
| 184 | A 2321593 | FLOATING BUSHING |
| 185 | A 2321598 | FLOATING BUSHING, F.P. LIFTER (WIDE 2-33/64)(SILICON BORZ.) |
| 186 | A 2321605-1 | PIN |
| 187 | A 2321803 | LEVAR ASSEMBLY, FUEL PUMP CONTROL SHAFT (INCLUDING ECCENTRIC PIN ASSLY.) |
| 188 | A 2321946 | ELEMENT, FILTER |
| 189 | A 2322164-1 | CONTROL RACK BUSHING |
| 190 | A 2322532 | SEAT FUEL PUMP SUPPORT |
| 191 | A 2322611-1 | NUT, F P SUPPORT COVER MACH (KNOB) |
| 192 | A 2331152 | SPRING SEAT LOCK, AIR & EXH. VALVE |
| 193 | A 2351034-1 | GEAR (15 TOOTH PINION GEAR) |
| 194 | A 2351035 | GEAR PINION (13 T) |
| 195 | A 23510617-1 | GEAR, NYLON |
| 196 | A 2351062-1 | GEAR (33 TOOTH BEVEL GEAR) |
| 197 | A 2351083-2 | DRIVE GEAR (LUB PUMP MACH) |
| 198 | A 2351124-1 | GEAR, EXT. SHAFT MACH. (79 TEETH)(PITCH DIA. 15.800)(WATER AND L.O.PUMP DRIVE)(79 TEETH) |
| 199 | A 2351175-2 | GEAR TACHOMETER DRIVE |
| 200 | A 2360141-1 | PLUNGER FOR OVERSPEED TRIP WEIGHT |
| 201 | A 2360183 | DRIVE GOVERNOR AND LINKAGE ASSEMBLY (DRIVE GOVERNOR ALCO PART NO. (2360183) & LINKAGE ASSEMBLY ALCO PART NO NOT AVAILABLE, THE LINKAGE ASSEMBLY IS FORMED BY NEAR 30 ITEMS) |
| 202 | A 2361049 | SHAFT |
| 203 | A 23610827 | LEVER, AT GOVERNOR (1800 AND 2400 HP) |
| 204 | A 2361093 | SPACER |
| 205 | A 2361096-1 | SPACER |
| 206 | A 2361125 | BUSHIING ,SPEED SETTING |
| 207 | A 2361185 | SHAFT & COUPLING MATCH SET |
| 208 | A 2361315-1 | SHAFT GOVERNOR CONTROL LINKAGE |
| 209 | A 2361374 | BEARING AND OIL SEAL RETAINER |
| 210 | A 2361484 – 1 | SUPPORT BEARING |
| 211 | A 2361594 | SPRING, SPEEDER SPRING SERVO |
| 212 | A 2361782 | CAP SCREW,1/4-20X1.1/8 IN |
| 213 | A 2361975 | COUPLING |
| 214 | A 2391304-1 | FACE PLATE L O P MACH. |
| 215 | A 2391312-1 | BEARING, FACE PLATE (FLANGED BRG.BUSH LOP MACH.) |
| 216 | A 2391314-1 | BEARING, BACK PLATE(FLANGED BRG.BUSH LOP MACH.) |
| 217 | A 2391351-1 | WEAR PLATE AT BACK LOP MACH. |
| 218 | A 2391352-1 | WEAR PLATE AT FACE LOP MACH. |
| 219 | A 2391824-3 | RETAINING RING, IDLER SHAFT |
| 220 | A 24010910 | WATER ELBOW |
| 221 | A 2401781 | GASKET BLOWER CASING |
| 222 | A 2402861-1 | O RING INJECTION TUBE TO CYL. HEAD BLOCK |
| 223 | A 2420021-2 | PISTON PIN WITH SLEEVE (2421071) |
| 224 | A 2420023 | PISTON PIN WITH SLEEVE |
| 225 | A 2420055 – 1 | PISTON RING SET ( CHROM PLATE LINE ) |
| 226 | A 2420058 | PISTON RING SET, CHROME PLATED |
| 227 | A 24210210 | PISTON RING SCRAPER |
| 228 | A 24210223 | RING, PISTON CONFORMABLE |
| 229 | A 2461082-1 | SPRING, AIR & EXH VALVE |
| 230 | A 2461083 | SNAP RING, VALVE SEAT INSERT |
| 231 | A 24610911 | TORSION SPRING, F P CONT. LEVER |
| 232 | A 24610934 | SPRING, TRIP CABLE |
| 233 | A 2491117 | BUSHING, SEAT |
| 234 | A 2491128 | CUP DISC MACH |
| 235 | A 2491313 | COVER WITH IDLER SHAFT |
| 236 | A 2491333 | IDLER WITH BUSHING |
| 237 | A 33341 | BOLT |
| 238 | A 4151036 | NUT SPECIAL (LOCK NUT FAN DRIVE) |
| 239 | A 4151072 | RING RETAINER |
| 240 | A 4151091-1 | OIL SEAL, FAN SHAFT FAN END |
| 241 | A 4261034 | AIR INLET CASHING |
| 242 | A 4261042-2 | NOZZLE RING TURBO MACH. |
| 243 | A 4261061 | BEARING CARRIER COMPRESSOR END MACH. |
| 244 | A 4261062 | BEARING CARRIER TURBINE END MACH. |
| 245 | A 4261071-1 | BEARING SLEEVE |
| 246 | A 4261081 | BEARING CARRIER RING |
| 247 | A 4261091 | FLOATING BUSHING |
| 248 | A 4261101 | THRUST WASHER (BLOWER END) |
| 249 | A 4261101 | THRUST WASHER TURBO |
| 250 | A 4261102-1 | THRUST WASHER TURBO |
| 251 | A 4261151 | NOZZLE RING GUIDE |
| 252 | A 4281091 | CASING |
| 253 | A 4281101 | IDLER SHAFT |
| 254 | A 4281102 | FAN SHAFT FAN DRIVE |
| 255 | A 4281103 | SPLINE SHAFT, FAN GEAR DRIVE |
| 256 | A 4281111 | SPACER IDLER SHAFT |
| 257 | A 4281112 | SPACER DRP.11700-D (SHAFT FAN DRIVE) |
| 258 | A 4281121 | COVER IDER SHAF FAN END |
| 259 | A 4281142 | FAN HOUSING |
| 260 | A 4281143 | IMPELLER FAN |
| 261 | A 4281171 | HOUSING |
| 262 | A 4281181 | CORE,AFTER COOLER |
| 263 | A 4281201 | OIL INLET FITTING, FAN DRIVE |
| 264 | A 4281211 | BUSHING FAN DRIVE SHAFT |
| 265 | A 4281221 | SLEEVE OIL INLET FAN SHAFT |
| 266 | A 4281231 | HUB, FAN DRIVE GEAR |
| 267 | A 4320012-1 | LIFTER ASSEMBLY ( F P CROSS HEAD) |
| 268 | A 4320021-1 | PUMP, FUEL INJECTION |
| 269 | A 4321021 | AUX. SPRING RETAINER, LOWER |
| 270 | A 4321022-2 | AUX. SPRING RETAINER, UPPER |
| 271 | A 4321032 | LIFTER, FUEL PUMP CROSS HEAD MACHINING |
| 272 | A 4321041 | F.P. CROSSHEAD CAM ROLLER |
| 273 | A 4321051 | BUSHING, FUEL PUMP CAM ROLLER |
| 274 | A 4321062 – 1 | FULCRUM PIN |
| 275 | A 4321063-1 | FULCRUM PIN |
| 276 | A 4321068 | PIN (FUELCUM ROLLER PIN) |
| 277 | A 4321091 | PLUNGER AND BARREL |
| 278 | A 4351011 | GEAR (34 TOOTH BEVEL GEAR) |
| 279 | A 4351013-1 | GEAR DRIVE |
| 280 | A 4351014 | IDLER GEAR, FAN DRIVE ASSEMBLY |
| 281 | A 4351019-1 | GEAR (13 TOOTH PINION GEAR) |
| 282 | A 4361061 | TRIP, LEVER |
| 283 | A 4361111 | OVER SPEED TRIP WEIGHT CARRIER |
| 284 | A 4361121 | HOUSING, CONTROL CABLE END |
| 285 | A 4361131 | ROD END |
| 286 | A 4361132 | CABLE END |
| 287 | A 4361141 | SHUTDOWN KNOB OVERSPEED TRIP |
| 288 | A 4361151 | BUSHING |
| 289 | A 4361152 | BUSHING |
| 290 | A 4361275 | LINK, PIVOT PIN |
| 291 | A 4361336 | CAP SCREW, OVER RIDING CYCLE, 1/4 IN-28X1.1/8 IN. |
| 292 | A 4401031-1 | TUBE, FUEL INJECTION |
| 293 | A 4461013 | AUX. SPRING F. P. CROSSHEAD, OUTER |
| 294 | A 4461015 | AUX. SPRING F. P. CROSSHEAD, INNER |
